Refinishing | Copper Valley Restoration Services

Kitchen Remodeling: Precisely What Tools You’ll Need to Restore Its Beauty

Posted on December 13, 2014 Written by Eric Leave a Comment

The tools you will probably need to rework your kitchen depend on how comprehensive your project is going to be and how much of the work you plan to do yourself. If you are going to undertake the entire kitchen, you’ll require some tools to remove the cabinets and flooring. To take out everything from the kitchen, the essential tools you will need are screwdriver, crowbar, power screwdriver, hammer and saw.

A large number of cabinets are held up by screws, therefore the screwdriver is needed to get the cabinets out without doing too much damage to the walls. If you wish to install the old cabinets in a different part of your home, then you will need to be careful when you remove them. If you basically plan to dump them, then you don’t need to be too concerned with the doors and hinges. To get the top cabinets down and out-of-the-way, you will also need a step ladder. If you want to take away the lower cabinets first, you probably want to take out the kitchen sink and appliances. If you don’t have a plumber for that, you will need wrenches or pliers to uninstall the sink, and garbage disposal, if you have one.

The cutting saw is going to be needed to take off the countertop off since you will be sawing them into small pieces. Taking off the flooring surfaces will be easy once you have removed the lower cabinet. At this time, everything should be out of the kitchen, in order to inspect the walls, and if need be, replace the sheet rock. If the walls and ceiling are in fair shape, you may simply need to do a little patch work or retexture. Once that is finished, you can replace the electrical outlets and switches and repaint the walls and ceiling. You will most likely need drywall and painting supplies as well as electrical tools. Before you buy, check to see if you possess the tools and supplies already.

Some people already have the tools necessary to do the job and also the experience. For others, not only is it going to be a discovering experience, but a number of tools will need to be purchased.

Feeling a little overwhelmed with what you need to know to finish your project? Or feel like the cost of the remodeling task would not suit your budget as of the moment?

Well, you can also opt to simply do some refinishing on your countertop and cabinets. This simple project could also transform the ay your kitchen looks.

There are companies who specializes in countertop and kitchen cabinet refinishing that can help you. If you’re around the Triad area, you may check out Specialized Refinishing, a company in Raleigh providing repair, restoration, refinishing, reglazing, and recoloring services for all types of surfaces.

Handy Guide to Pressure Washing Your Deck

Posted on March 24, 2014 Written by webmaster Leave a Comment

Cleaning your deck has a great side and a bad side. The great side is that with a pressure washer, you are able to rid the wood of grime and other unusual materials which have made the lumber their home.

The dreadful side is you could do a number in your deck if you don’t understand what you’re doing. When you possess the incorrect nozzle on the wand, get the hint too near the wood or crank the machine up-to full blast, you stand to ruin your deck.

Those folks who get a power washer from a nearby lease business can fasten a unit that can crank-outside well over 4-thousand pounds per square inch of pressure. At that rate, it is possible to literally make your own Mount Rushmore on a brick.

To make sure you don’t turn your deck right into a mound of toothpicks, here are some tips regarding how you are able to manage the job safely, quickly and without causing expensive damage.

1.Nozzle and Point

We already mentioned how powerful this equipment can be. That just means you’ll should choose a few matters. Let’s start together with the nozzle or the tip. To clean soft woods like pine or cedar, attach a fan tip using a 40-to-60 degree output signal. This maximizes the area that you’ll cover and disperses-outside the level of pressure over a larger surface.

As for pressure, you are only going to want about 700 psi of electricity. You shouldn’t ramp up the washer higher than 1200 psi. Bottom line, begin low, just using more pressure if you genuinely require it.

When you press the trigger, don’t train it at a window or the children. Start out about 2-feet over the wood surface, slowly closing in to around 16-inches from the deck. If you’re a foot-or-closer to the wood, pull up, pilot!

Clever move could be to try out things on a portion of your deck that is a little out of the way. Just in case you make any mistakes, nobody will discover that which you screw up if they can not see it.

2.Technique

Begin in the 600 psi degree. You can always boost the pressure, but start low. Squeeze the trigger several feet in the surface. Slowly lower the wand before you get to the sweet spot of 16-inches. Brush the arm back-and-forth. Notice what is occurring and pay attention. You might need to correct the pressure with respect to the outcomes.

Be consistent together with your sweeping movement. Start at your home’s foundation and move from the house. Do Not go against the grain.

3.Wood Fibers

When lumber gets wet, the fibers increase to the occasion. You do not need to make splinters when pressure washing your deck. To eliminate this from occurring, get prepared to sand.

— Use an orbital sander with a 5-inch pad

— On the surface and handrails, stroke the wood with an 80-grit sand paper

Sanding the finished deck serves a few functions. It’ll make the lumber more porous so the stain and sealer will soak into the grain.

Why Tub and Tile Reglazing?

Posted on March 24, 2014 Written by webmaster Leave a Comment

I’m often asked why someone would pick bathtub and tile reglazing (also called refinishing) over other processes of addressing unsightly toilets. The reply is simple in that if you’re looking to modernize your bathroom you really have only three alternatives; you can entirely rip out and replace that which you currently have, you can cover your fixtures up with a lining, or you can simply refinish your toilet in a way that’s attractive, inexpensive, and low maintenance.

How Does Bathtub And Tile Reglazing Look?

When tub and tile reglazing are completed by a trained tech, imperfections in your bathtub or tile, like chips or scratches, will be fixed throughout the refinishing process. Using the extensive variety of colors that are accessible, you can find a match to any decor you already have in place, so breathing new life into your bathtub or tile. http://specializedrefinishing.com/

How Long Does It Take To Finish a Tub And Tile Reglazing Endeavor?

It requires a tech about 6 to 8 hours to finish your bathtub and tile reglazing endeavor. If your technician is using high quality merchandises, the finish should be dry to the touch in approximately 2 – 4 hours, though you should not use your tub for at least 24 hours after the program. Compare this to the time, and multiple appointments, it can take to fully rip out and replace or reline your tub and tile, and you will see that reglazing may be the best choice for you.

Money Issues

Refinishing functionally sound tubs and tile can save you thousands compared to the cost of replacing or lining them. Furthermore, refinished tubs and tile have a durable finish that, if appropriately maintained, can last over 10 years and if finished by a reputable business, should come with a warranty that backs up the quality of service being guaranteed.

As you can find, there are many advantages of reglazing your bathtub or tile over entirely replacing or relining them. Call the best Raleigh tub refinishing company, Specialized Refinishing to find out more today.